Dr.fixit Waterproofing chemicals & compounds

Product Details:

Dr.Fixit Distributors & Dealers in ludhiana punjab
Description
Dr. Fixit Fastflex is a two component acrylic cementitious coating system for waterproofing of wet areas and
any water retaining structures such as swimming pools and water features. It provides strong bonding and
excellent resistant to hydrostatic water pressure by forming highly elastic seamless coating over the applied
concrete surfaces.
Areas of Application
} Any concrete, cement or masonry surface that are subject to moisture ingress.
} Swimming pools, water features and water tanks.
} Bathrooms, toilets, balconies, planters etc.
Features & Benefits
} Seamless, impervious membrane.
} Elastomeric.
} High film build-up.
} Excellent adhesion to concrete and masonry substrates.
} Low VOC.
} Easily applied by brush, roller or trowel.
} Can be applied on damp surfaces.
Method of Application
1 SURFACE PREPARATION
} The surface of application must be thoroughly prepared by mechanical means, to remove all loose particles,
laitance, etc.
} Oil and grease, if any, must be de-greased with suitable solvents. It then must be washed off with jet of water
and brought to touch dry state.
} Any surface undulations, cracks and crevices must be duly filled or repaired with cement sand mortar mixed
with latex polymers such as Dr. Fixit Pidicrete URP.
} All vertical up-stands & junctions /corners are provided with 45° fillet with Polymer Modified Mortar (PMM),
mixed with Dr. Fixit Pidicrete URP all around the periphery of the junction.
} Substrate must be in a "Saturated Surface Dry" (SSD) condition (damp, without standing water) prior
to application.
2 MIXING
} Using a slow speed mechanical mixer and a clean suitable mixing vessel, slowly add the powder component to
the liquid polymer and stir until a smooth and homogenous slurry, is achieved.
} Allow the mixed slurry to stand for 5 – 10 minutes before use.
} Do not dilute with water.
3 APPLICATION
} All the pipe inserts or sanitary fittings should have been fitted grouted with suitable products from the Dr. Fixit
range well before taking up the application.
} The surface of application must be pre-wetted thoroughly with water & brought to a touch dry state. Take up the
first coat application with a stiff nylon brush. Work well into the substrate, to ensure that all small undulations
are completely filled with the coating.
} Provide and lay 45 GSM glass fibre mesh over the angle fillet when the first coat in still wet.
} 6 to 8 hrs after completion of first coat, take up second coat application in a direction perpendicular to the

Product Details:

Description
Dr. Fixit Pidifin 2K is a acrylic cementitious, polymer modified flexible, waterproofing & protective coating
composed of best quality Portland cement, properly selected & graded aggregates, additives & acrylic emulsion
polymer as a binder. It is applied to waterproof and protect concrete and masonry substrates.
Typical Application
} Excellent as a waterproof coating for bathrooms, kitchen sinks, balconies, etc.
} Ideal as a coating for waterproofing of roofs, chhajjas, canopies, etc.
} As waterproof coating on internal sides of domestic water tanks.
} Can be applied over internal damp walls and concrete surfaces due to its excellent bonding.
Features
} Flexible coating
} This product can be used for both positive and negative side waterproofing due to its excellent bonding
} Excellent adhesion to concrete and masonry surfaces
} Excellent resistance to ingress of water
} Confirms to portable water contact parameters.
} Non-toxic with low VOC content
Packaging
3 kg, 9 kg, 15 kg, 30 kg & 90 kg
Method of Application
1 SURFACE PREPARATION
} The surface of application must be thoroughly prepared by mechanical means, to remove all loose particles,
laitance, etc.
} Oil and grease, if any, must be de-greased with suitable solvents. It then must be washed off with jet of water
and brought to touch dry state. Any surface undulations, cracks and crevices must be duly filled or repaired with
cement sand mortar mixed with latex polymers such as Dr. Fixit Pidicrete URP.
} All vertical up-stands & junctions /corners are provided with 45° fillet with Polymer Modified Mortar (PMM),
mixed with Dr. Fixit Pidicrete URP all around the periphery of the junction.
} Substrate must be in a "Saturated Surface Dry" (SSD) condition (damp, without standing water) prior to
application.
2 MIXING
} Shake the liquid component well to a homogenous milky colour.
} Use heavy duty slow speed mechanical mixer fitted with a suitable paddle for mixing the two components of the
material.
} In a mixing vessel, slowly add the powder component in to the liquid under continuous stirring. Continue to stir
thoroughly to achieve a lump free homogenous slurry.
3 APPLICATION
} It is important that any pipe inserts or sanitary fittings should have been fitted grouted with suitable products
from the Dr. Fixit range well before taking up the application.
} Grout pipe inserts using Dr Fixit Bathseal Tape and Dr Fixit Bathseal Grout.
} It is mandatory that all works of plumbing and sanitation must be complete before taking up application of
Dr. Fixit Pidifin 2K.