Waterproofing Chemical

Product Details:

Main Uses:

Safe with metals (except zinc and galvanised steel), wood, glass, plastic and rubber. No corrosive action. Penetrates oil and grease.

Advantages:

Rapid Action:

• Safe with metals (except zinc and galvanised steel), wood, glass, plastic and rubber. No corrosive action. Penetrates oil and grease.

Product Details:

Brushbond UltraFlexpage 1 of 2High Performance & Ultra fl exible polymer modifi ed elastomeric waterproofi ng membrane system for concrete and masonry surfaces.UsesBrushbond UltraFlex, when fully cured, provides a seamless Elastomeric waterproof membrane for use in roof areas, wet areas, bathroom, water tanks, swimming pools, reservoirs, precast joints where a tough elastomeric water tight membrane is requiredAdvantages Low VOC. Can be applied to damp substrates. No primer required. Elastomeric - able to bridge cracks Able to take foot traffi c when cured. Factory pre-blended two component system ensure quality control at site control.DescriptionBrushbond UltraFlex is a two component polymer modifi ed waterproof membrane which is supplied in readymix kits. When mixed, an easily brushable coating is produced. It can simply be applied by a stiff brush, roller, or trowel to obtain the desired thickness.Brushbond UltraFlex consists of specially selected cements, graded hard wearing aggregates and additives supplied in powder form together with a liquid component of polymers providing exceptional adhesion, resiliency, fl exibility, toughness and durability.Standards complianceBrushbond UltraFlex conforms to the requirements of: DIN 1048, Part 5, 1991 ISO 7783:2018 ASTM D412 : 2013 Brushbond UltraFlex is deemed to be suitable for use with potable water sources as tested as per USFDA CFR 175-300Technical Support Fosroc off ers a comprehensive range of high performance high quality, construction products. In addition to a wide range of quality products, Fosroc off ers a technical support package to specifi ers and contractors which includes assistance with product selection and technical advice from staff with unrivalled experience in the industry. PropertiesPot life at 27CApprox. 1.0 hr:Adhesion to substrate (ASTM D4541:2002)> 1.0 N/mm2Shore A hardness (ASTM D2240:201079Tensile strength N/mm2) (ASTM D412-2013)>1.50 N/mm2Mixed Density @ 27oC1.50 + 0.1 g/ccRapid Chloride Permeability (ASTM C1202)very lowMigration test (CFR 175-300 of US FDAPassElongation at break (ASTM D412-2013)> 150%Water Permeability EN12390 (part8) 2008) Negative PressureNilWater vapour transmission (ISO 7783:2018) 20.81 g/m2.hrCrack bridging: (ASTM C1305) 1.0 mmFoot traffi c*6 hr +/- 1 hrNote: The typical physical properties given above are derived from testing in a controlled laboratory environment. Results derived from testing fi eld-applied samples may vary, dependent on actual site conditions.Application InstructionsPreparationAll surfaces which are to receive Brushbond UltraFlex coating, must be free from oil, grease, wax, dirt or any other form of foreign matter which might eff ect adhesion. Spalled and deeply disintegrated concrete should be removed to sound concrete and repaired with Renderoc System.MixingThe Brushbond UltraFlex Liquid concentrate is poured from the plastic container into the metal drum supplied and mixed mechanically with a slow speed drill (350-450 rpm) fi tted with a Fosroc Mixing Paddle (MR3). Add the powder component gradually to the liquid avoiding lump formation and mix for 4-5 minutes until a smooth consistent mix is achieved. Use the material within the recommended pot life.ApplicationFor best results damp the surface before coating with Brushbond UltraFlex. Use a short, stiff bristle brush preferably 120 to 200 mm in width. Apply like a paint using one or two coats as required. For trowel application, ensure that the substrate is levelled and repaired of any undulations or pot holes. Spray application should be carried out using the Graco make TEXSPRAY RTX5500px/ToughTek F800e/similar make

Product Details:

Conplast WL Xtra
Uses
To minimise permeability and increase the waterproofi ng
properties of concrete, plaster and cement sand mortars for
critical applications like roof slabs,screeds, basements, external
plastering, bathroom fl oors, water tanks, sumps, drains etc.
Feature and Benefi ts:
 Advanced Technology : New generation molecule
yields high performance concrete. Suitable for any
grade of concrete including higher grades.
 Corrosion resistant: Meets the requirements of
Japanese code JIS Z1535 (modifi ed) fi rst of kinds in
the integral water proofi ng range.
 High Strength : Due to better dispersion of cement
particles and helps in the better degree of hydration
yielding high strength compared to control.
 Cohesive Mix : Improves workablity and cohesiveness
of the concrete.
 Durability : Improves durability due to reduction in
permeability of concrete and corrosion resistance of steel.
Standards compliance
Conplast WL Xtra conforms to IS:2645-2003.
Description
Conplast WL Xtra is a dark brown liquid based on cement
dispersion polymers which mixes readily with water and
therefore disperses evenly.
Conplast WL Xtra waterproofs by improving the quality of the
concrete or mortar. It reduces the water demand for required
workability and minimises segregation and bleeding. Thus it is
more effi cient compared to traditional powder and conventional
integral waterproofi ng compounds as its use results in two fold
improvement of concrete or mortar.
Technical support
Fosroc provides a technical advisory service for onsite assistance
and advice on admixture selection, evaluation trials and
dispensing equipment. Technical data and guidance can be
provided for admixtures and other products for use with fresh
and hardened concrete.

Product Details:

Single component acrylic polymer for cement based
waterproof composite coating membrane.
Uses
Provides an effective and economical method of
waterproofing to concrete and masonry surfaces, by mixing
with cement and application by brush.
Advantages
„ Non - toxic, non-flammable and user friendly
„ Provides a tough, impermeable waterproof membrane
„ Can be applied by brush, on horizontal and vertical surfaces
„ Excellent adhesion to concrete and masonry surfaces
„ Protects concrete and mortar from natural elements such
as wind, rain, sunlight
„ Breathable - allows inside water vapour to escape
Description
Hydroproof is formulated to be mixed with cement on site or
simply brush applied over concrete or masonry surfaces to
provide an effective waterproof membrane.
Technical support
Fosroc provides a technical advisory service supported by a
team of specialists in the field.
Areas of application
Below sloping screed or waterproof plaster on :
„ Roofs, terraces and balconies as a sandwich layer
„ Pools and fountains
„ Reservoirs and channels
„ End walls subjected to rain
Properties
Water absorption : 1% maximum
Pot life at 300
C : 30 min.
Application temperature : Not less than 100
C
Toxicity : Non-toxic
Bond strength to concrete : Approx. 1 N/mm2
Application instructions
Preparation
All surfaces to be treated with Hydroproof must be thoroughly
cleaned by a wire brush or other mechanical means, to
remove all dust, laitence or debris. The surface must also be
free from oil, grease, wax or any other form of foreign matter
which might affect adhesion. Spalled and deeply
disintegrated concrete or mortar must be removed to a sound
substrate and repaired suitably before coating.

Product Details:

Other Details:

• Rapid setting cement based, water leak plugging mortar

Product Details:

we “R.S. Enterprises” are a leading Wholesale Trader and Service Provider of a wide range of Waterproofing Chemical, Glass Railing, Fosroc Chemical, etc. 

Product Details:

Nitocote ET550 is a thixotropic, tar extended, two pack epoxy formulation, containing inert, reinforcing fillers and a special blend of solvents

Product Details:

Hydroproof Xtra - FosrocHydroproof Xtra is formulated to be mixed with cement on site or simply brush applied over concrete or masonry surfaces to provide an effective waterproof??.

Product Details:

Main Uses:

• Suitable for sealing water tanks,reserviors,toilets and bathrooms,balconies and basements as well as filling blowholes,cracks,imperfections and for providing concrete surfaces with a uniform appearance.

Advantages:

• Minimum surface preparation needed
• Excellent adhension.Bonds directly to porous and non- porous surfaces
• Waterproof and non-toxic-Ideal for potable water tanks
• Excellent for damp-proofing basements below ground
• Breathable-Allows transmission of water vapour from interior of building
• High resistance to carbon dioxide and chloride ion diffusion
• Can fill the honeycomds, dot surfaces and concrete with potholes

Description:

• Brushbond comprises a two component acrylic polymermodified cementitious coating supplied in ready to mix kits.Brushbond can be simply applied by stiff brush, roller, sprayor trowel to obtain the desired texture

Note: For potable water applications, please refer toNitocote CM210 and Brushbond FLX lll datasheets


Acrylic polymer modified protective/decorative coating:

• The protective coating shall comprise specially selectedcements, graded hardwearing aggregates and additivessupplied in powder form together with a liquid component ofblended acrylic co-polymers and wetting agents. The total dryfilm thickness of the coating shall be not less than 2 mm andshall be capable of providing resistance to wear and weatherand good chemical resistance to mild inorganic acid solution,diesel oil, gasoline, chlorides, de-icing salts, effluents andorganic solvents

Instructions for Use:

Preparation:

• All surfaces should be dry and free from contamination suchas oil, grease, loose particles, decayed matter, laitance, andall traces of mould release oils and curing compounds. Thisis best achieved by lightly grit-blasting the surface.
• Where moss, algae or similar growths have occurred,treatment with a proprietary biocide should be carried out afterthe grit-blasting process
• Spalled and deeply disintegrated concrete should be removedto sound concrete and repaired with a Fosroc repair system.For further advice, consult the local Fosroc office.
• It is essential that all surfaces to be treated be pre-soakedwith clean water prior to application of Brushbond

Mixing:

• Brushbond liquid should be poured from the plastic containerinto the metal drum provided. For brush application consistencymix with a slow speed drill (500 r.p.m.) fitted with a FosrocMixing Paddle (MR3)
• The powder component should be added gradually to the liquidto avoid lump formation and mixed for 2 to 4 minutes.
• Brushbond should be immediately used after mixing. Do notmix more material than can be used within the pot life. Keepmixing Brushbond during the application.

Application:
Application of Brushbond on hot substrates (i.e. over 40oCsurface temperature) will need the prior application of a primercoat. Mix Brushbond and water in slurry like consistency andapply Brushbond over the primer whilst it is still wet.

For best results, surfaces should be damp. In order to obtainthe protective properties of Brushbond, it is important that thecorrect rates of application are observed.
Use a short stiff brush (preferably 120 - 200mm width) andapply in one or two coats as required.

 Other Details:

• Cementitious acrylic waterproof coating

Product Details:

Chryso Excem GP80 is a high-performance admixture designed to enhance the properties of cementitious materials such as concrete and mortar. Here's a description:

1. Chryso Excem GP80 is a premium-grade admixture manufactured by Chryso, a leading provider of construction chemicals.
2. Formulated with advanced technology, it improves the workability, durability, and performance of concrete and mortar mixes.
3. Acts as a water-reducing agent, allowing for higher slump or workability without compromising strength.
4. Enhances the cohesiveness and flow of concrete, facilitating easier placement and compaction.
5. Reduces the risk of segregation and bleeding, resulting in a more uniform and homogeneous mixture.
6. Improves the early and ultimate compressive strength of concrete, leading to enhanced structural performance.
7. Increases resistance to freeze-thaw cycles, chemical attack, and abrasion, extending the service life of concrete structures.
8. Compatible with various cement types and mix designs, providing versatility in application.
9. Suitable for a wide range of concrete applications including residential, commercial, and infrastructure projects.
10. Chryso Excem GP80 is the preferred choice for contractors, ready-mix producers, and engineers seeking high-quality admixtures to optimize the performance of their concrete mixes.

Product Details:

Dr. Fixit 112 Pidifin 2K is a two-component, cementitious waterproofing coating manufactured by Pidilite Industries Ltd., designed to provide durable and effective waterproofing for various construction surfaces. Here's an overview of Dr. Fixit 112 Pidifin 2K:
Composition: Dr. Fixit 112 Pidifin 2K is formulated with high-quality cement, additives, and polymers to create a flexible and waterproof coating. It consists of two components - Part A (liquid) and Part B (powder) - which are mixed together in the prescribed ratio to form a workable paste.
Cementitious Formula: Being cement-based, Dr. Fixit 112 Pidifin 2K offers excellent adhesion to concrete, masonry, and other porous substrates. It penetrates into the substrate's pores, forming a strong bond and providing long-lasting waterproofing protection.
Flexible and Crack Bridging: The coating exhibits flexibility and crack-bridging properties, allowing it to accommodate minor substrate movements and hairline cracks without compromising its waterproofing integrity. This feature ensures reliable protection against water ingress and moisture damage.
Versatile Application: Dr. Fixit 112 Pidifin 2K can be applied to both horizontal and vertical surfaces, including roofs, terraces, balconies, basements, and exterior walls. It is suitable for use on new construction projects as well as for repairing and waterproofing existing structures.
Resistance to Water and Chemicals: Once cured, Dr. Fixit 112 Pidifin 2K forms a seamless and impermeable membrane that effectively repels water, preventing water penetration and moisture seepage into the building interior. It is also resistant to chemicals, ensuring durability in harsh environmental conditions.
Easy Application: The two-component system of Dr. Fixit 112 Pidifin 2K allows for easy mixing and application. The liquid component is added to the powder component and mixed thoroughly to achieve a smooth, lump-free paste, which can then be applied using a brush, roller, or spray equipment.
Long-Term Protection: Dr. Fixit 112 Pidifin 2K provides long-term protection against water damage and deterioration, extending the lifespan of the waterproofed structure and reducing the need for costly repairs and maintenance.
Packaging: Dr. Fixit 112 Pidifin 2K is available in convenient packaging sizes, with the 15kg option being suitable for medium to large waterproofing projects.

Product Details:

Hydroproof Xtra:

Hydroproof Xtra is formulated to be mixed with cement on site or simply brush applied over concrete or masonry surfaces to provide an effective waterproof membrane.

Main Uses:

Non - toxic, non-fl ammable and user friendly

Provides a tough, impermeable waterproof membrane

Can be applied by brush, on horizontal and vertical surfaces
 
Excellent adhesion to concrete and masonry surfaces
Protects concrete and mortar from natural elements such as wind, rain, sunlight
Breathable - allows inside water vapour to escape
 

Product Details:

STARBOND STARCRETE ACR 30 is an aqueous dispersion of Acrylic Co-Polymer, specifically designed for modified Portland cement compositions. Mortar modified with ACR 30 has improved physical strength, and superior adhesion to old concrete, masonry, brick, and many other surfaces. The dispersion contains an anionic emulsifier system and is free from film forming aids, solvents and plasticizers. BENIFITS ??? Easy to use. ??? Improves bond Strength. ??? Increases durability under freeze/thaw cycling. ??? Reduce cracking through increased mortar flexural strength. ??? Increases mortar wear resistance under rubber wheeled traffic. ??? Repair mortar offers greater impact resistance. ??? Due to low permeability, it can be used for waterproof sealing and lining of tanks etc. USES ??? Toppings, patches and leveling course. ??? Thin Sets, terrazzo, stucco and bonding slurries. ??? Repairs utilizing spray or fill coats. ??? Heavy duty floors & high strength of concrete bonding. ??? Repairs to pre-cast structural members. ??? Architectural panels, bridge decks & high-way repairs. ??? Resistance to mild chemicals, grease, alkaline and acid. TECHNICAL DATA SHEET Appearance Free Flowing liquid Colour Milky White Solubility With water Soluble Non-Volatile content 28 ± 5 Specific Gravity 1.0 ± .05 Compatibility with Canvas cloth Compatible pH 7-9 Water Resistance Excellent Flammability Non-Flammable Coverage 28-30 sq.ft per kg for 2coats METHOD OF APPLICATION For use as a Bonding Slurry Coat ??? Clean and wet the surface 24 hours prior to application ??? Mix ACR 30 & Cement 1:2 by volume. ??? Apply single coat and place the mortar while the coat is still wet. For use as a Repair Mortar or Render Mix ACR 30 Cement: Washed Sand in the ratio of 2:5:15. Dry mix cement and sand first and then add ACR 30. Mix for 3 minutes. Add water as required to attain requisite consistency of mortar. For use as a Cement Grout ??? Mix ACR 30: Water : Cement in the ratio of 1:2:3. Add ACR 30 to water first and then mix cement to the mixture. ??? Apply the slurry on the surface For use in Reinforced Steel Priming ??? Wet the surface prior to application ??? Apply one coat of ACR 30 mixed with cement (1:2 by volume) as a slurry to all exposed steel surfaces. Allow to dry. ??? Apply 2nd coat and dry again. For use as a Water proof Coating ??? Prime the prepared surface with ACR 30 admixed with 3 litre of water by brush, roller & spray. ??? Apply first coat with mixture of ACR 30: Cement in ratio of 1:2 by weight. ??? Apply top coat with same mixture as above. Covered 28-30 sq. feet for 2 coats.

Product Details:

Main uses

• Ensure even concrete surface
• Reduces opportunity of damage to formwork, extending usable life.
• Minimises cleaning of formwork before re-use
• Suitable for use with virtually all types of formwork.
• Inhibits corrosion of steel formwork.

Product Details:

A waterproofing membrane is a thin layer of water-tight material that is laid over a surface. This layer is continuous and does not allow water to pass through it. For example, on a flat terrace, a waterproofing membrane could be laid above the structural slab and below the finish tiles

Product Details:

Protects Interiors From Water DamageThis includes walls, floors, the foundation and even the insulation. ... Waterproofing your home protects the walls from creating a seepage. It will help prevent water damage from occurring, promoting in your fledgling building a healthy, strong start.

Product Details:

Renderoc HSXtra is suitable for hand and spray application for repairs where high load bearing is required. Typical applications would include, but not be limited to, the following: ??? Vertical and overhead repairs to restore ‘covercrete’. ??? General concrete and masonry repairs. ??? Voids greater than 10 mm deep. ??? Repairs to honeycombing. ??? Larger scale repairs where formwork cannot be erected. 

If you're in need of roof repairing services, it's essential to find a reputable and reliable contractor who can effectively address your roofing issues. Here's a guide on what to look for and expect from a professional roof repair service:

1. Assessment: A professional roofing contractor will start by conducting a thorough inspection of your roof to assess the extent of the damage and identify any underlying issues that may need attention.

2. Recommendations: Based on the assessment, the contractor will provide recommendations for the necessary repairs or replacements needed to restore the integrity of your roof. They should explain the options available to you and help you make informed decisions.

3. Estimate: The contractor should provide you with a detailed estimate outlining the scope of work, materials required, labor costs, and project timeline. Make sure the estimate is clear and transparent, with no hidden fees or surprises.

4. Experience and Expertise: Look for a roofing contractor with extensive experience and expertise in repairing roofs similar to yours. Check their credentials, certifications, and customer reviews to ensure they have a proven track record of delivering quality workmanship.

5. Licensing and Insurance: Verify that the roofing contractor is properly licensed and insured to perform roof repairs in your area. This protects you from liability in case of accidents or property damage during the repair process.

6. Quality Materials: Ensure that the contractor uses high-quality materials and products for the repairs. Quality materials contribute to the longevity and durability of your roof, reducing the need for frequent repairs in the future.

7. Guarantees and Warranties: A reputable roofing contractor should stand behind their workmanship and offer guarantees or warranties on the repairs performed. This gives you peace of mind knowing that they will address any issues that may arise after the repair is completed.

8. Safety Measures: Safety should be a top priority during roof repairs. The contractor should follow proper safety protocols and use the necessary safety equipment to protect their workers and your property.

9. Communication: Effective communication is essential throughout the repair process. The contractor should keep you informed of the progress, any unexpected issues encountered, and any changes to the timeline or budget.

10. Cleanup and Disposal: After completing the repairs, the contractor should thoroughly clean up the work area and dispose of any debris or materials removed from your roof. Leaving your property clean and tidy is a sign of professionalism.

Product Details:

Dr. Fixit 113 Fast Flex is a specialized waterproofing coating manufactured by Pidilite Industries Ltd., designed to provide effective protection against water ingress and moisture damage in various construction applications. Here's an overview of Dr. Fixit 113 Fast Flex:
Composition: Dr. Fixit 113 Fast Flex is a two-component, flexible waterproofing coating comprising a liquid component (Part A) and a powder component (Part B). When mixed together in the prescribed ratio, they form a flexible, elastomeric membrane that adheres tightly to substrates and provides excellent waterproofing properties.
Fast-Curing Formula: As the name suggests, Dr. Fixit 113 Fast Flex is formulated with a fast-curing formula that allows for rapid application and quick drying times. This feature helps expedite construction schedules and minimizes downtime, allowing for faster project completion.
Flexibility and Crack Bridging: The elastomeric nature of Dr. Fixit 113 Fast Flex enables it to accommodate substrate movement, thermal expansion, and minor structural cracking without compromising its integrity. It forms a seamless, flexible membrane that bridges cracks and gaps, ensuring long-term waterproofing performance.
Excellent Adhesion: The coating exhibits excellent adhesion to a variety of substrates, including concrete, masonry, metal, and wood. It forms a strong bond with the substrate, preventing water infiltration and providing durable waterproofing protection.
Versatile Application: Dr. Fixit 113 Fast Flex can be applied to both horizontal and vertical surfaces, making it suitable for a wide range of applications, including roofs, terraces, balconies, basements, and exterior walls. It can also be used as a protective coating for water tanks, swimming pools, and other water-retaining structures.
Resistance to Weathering and Chemicals: The waterproofing membrane is resistant to UV radiation, weathering, and chemical exposure, ensuring long-term durability and performance in outdoor environments. It withstands exposure to sunlight, rain, temperature fluctuations, and chemical pollutants without deteriorating or losing its waterproofing properties.
Ease of Application: Dr. Fixit 113 Fast Flex is easy to mix, apply, and spread using a brush, roller, or spray equipment. The two-component formulation allows for precise mixing and consistent application, ensuring uniform coverage and thickness across the substrate.
Cost-Effective Solution: Dr. Fixit 113 Fast Flex offers a cost-effective solution for waterproofing projects, providing durable protection against water damage and reducing the need for costly repairs and maintenance over time.

Product Details:

Dr. Fixit Fastflex Waterproofing Coating is a premium-grade waterproofing solution designed to provide long-lasting protection for various surfaces. Here's an overview:

1. High-Performance Coating: Dr. Fixit Fastflex is a high-performance elastomeric waterproofing coating formulated to withstand harsh weather conditions, UV exposure, and water ingress.

2. Elastomeric Properties: The coating exhibits elastomeric properties, allowing it to stretch and bridge cracks, gaps, and voids in the substrate, providing seamless waterproofing protection.

3. Flexible and Crack-Bridging: Dr. Fixit Fastflex can accommodate structural movements and settlement without compromising its waterproofing integrity, making it ideal for both new construction and renovation projects.

4. Superior Waterproofing: The coating forms a durable and seamless barrier that effectively seals surfaces such as roofs, terraces, balconies, walls, and concrete structures, preventing water penetration and moisture damage.

5. Easy Application: Dr. Fixit Fastflex is easy to apply using a brush, roller, or spray equipment, facilitating quick and efficient installation. It can be applied to vertical and horizontal surfaces with ease.

6. Versatile: Suitable for a wide range of substrates including concrete, masonry, metal, wood, and asphalt, Dr. Fixit Fastflex offers versatility in waterproofing applications.

7. Long-Lasting Protection: The coating provides long-lasting protection against water ingress, efflorescence, algae, and fungus growth, ensuring the durability and longevity of the treated surfaces.

8. Resistant to UV Degradation: Dr. Fixit Fastflex is resistant to UV degradation and color fading, maintaining its aesthetics and performance even in exposed outdoor environments.

9. Compliance and Certification: The product complies with relevant industry standards and is backed by certifications and approvals, ensuring quality and reliability.

10. Trusted Brand: Dr. Fixit is a trusted brand in the construction industry, known for its innovative waterproofing solutions and commitment to quality and customer satisfaction.

Product Details:

Fosroc nitobond EP standard

Additional Information:

• Item Code: 3824
• Production Capacity: 10000
• Delivery Time: 2 days
• Packaging Details: 1 litre or 4 litre

Product Details:

STP Shalicrete Acrylic Polymer is a specialized waterproofing chemical manufactured by STP Limited, designed to provide effective protection against water ingress and moisture damage in construction applications. Here's an overview of STP Shalicrete Acrylic Polymer:

1. Composition: STP Shalicrete Acrylic Polymer is formulated with high-quality acrylic polymers, additives, and modifiers. This unique composition imparts excellent waterproofing properties, flexibility, and durability to cementitious materials.

2. Waterproofing Properties: Shalicrete Acrylic Polymer creates a seamless and impermeable barrier when applied to concrete, mortar, or masonry surfaces. It effectively prevents water penetration and moisture ingress, protecting the structure from water-related damage such as efflorescence, dampness, and corrosion.

3. Flexibility and Crack Bridging: The acrylic polymer in Shalicrete enhances the flexibility of the waterproofing membrane, allowing it to accommodate substrate movement, thermal expansion, and minor structural cracking without compromising its integrity. This flexibility helps bridge cracks and gaps, ensuring long-term waterproofing performance.

4. Application: Shalicrete Acrylic Polymer can be applied by brush, roller, or spray onto prepared substrates, including concrete, cementitious renders, and masonry surfaces. It can be used as a standalone waterproofing membrane or as a primer before the application of additional coatings or finishes.

5. Versatility: Shalicrete Acrylic Polymer is suitable for a wide range of applications, including:

   • Roof waterproofing for flat roofs, terraces, balconies, and podium decks
   • Basement waterproofing for foundations, retaining walls, and underground structures
   • Waterproofing of wet areas such as bathrooms, kitchens, and swimming pools
   • Protection of concrete structures, bridges, tunnels, and culverts from water ingress

6. UV Resistance: The acrylic polymer in Shalicrete provides UV resistance, making it suitable for exterior applications exposed to sunlight and weathering. It retains its flexibility and waterproofing performance even under prolonged exposure to harsh environmental conditions.

7. Compatibility: Shalicrete Acrylic Polymer is compatible with various cementitious materials, including Portland cement, cement-sand renders, concrete blocks, and brickwork. It can be applied to both new construction and existing structures, offering versatile waterproofing solutions for different project requirements.

Product Details:

An expansion joint, or movement joint, is an assembly designed to hold parts together while safely absorbing temperature-induced expansion and contraction of building materials, and vibration, or to allow movement due to ground settlement or seismic activity

Product Details:

STARPROOF WF-MB-602 is cold applied liquid waterproofing membrane, specially designed from a blend of special resin and rubber, reinforced with special water repelling fillers, minerals stabilizers and gelling agent. USES Ideal waterproofing system for concrete roofs, polyurethane foam slabs, polyester built up roofs, maintenance of existing roofs, masonry and concrete walls, bathrooms, basements, bridges, decks, metal surfaces etc. Used as a sandwich membrane in new construction and as surface treatment on existing slabs 

Product Details:

CICO TAPECRETE RTU is a two pack polymer modified cementitious elastomeric protective and waterproof coating. When it hardens it develops excellent bonding property to most building materials. It is suitable in both interior and exterior building and all other civil engineering applications. Cured film of CICO TAPECRETE RTU prevents dampness in buildings tanks, roofs and other concrete structures permanently.USES For sealing fine “hairline” cracks in concrete structures. For waterproofing of concrete water tanks, pools etc. For exterior waterproofing of basement walls in new buildings. For all kinds of damp proofing and waterproofing in concrete, mortar, rendering, brickwork and block work. For sealing internal basement and cellar walls against dampness. For Water proofing of Roof Gardens.ADVANTAGES Excellent adhesion to sound and prepared surfaces. Pre-measured packs – need only mixing. Easy to apply by brush. Excellent barrier coating for CO2 , acid gases and chloride ions. Non-toxic suitable for contact with drinking water. Non-Corrosive to steel or iron, non￾inflammable. Protects against the effects of concrete carbonation, efflorescence or salt petering. Protects superbly against water penetration.TECHNICAL DATATwo packs: Pack A Grey Powder, White PowderPack B White liquidColour of the hardened film Grey, WhiteDensity of Mixed Components 1.7 kg / ltr.Time for working at 30° C 20 to 30 minutes 60% R. H.Coating required Two (minimum)Application temperature minimum 2°Cmaximum 45°CAdhesive strength with concrete20 kg/cm2 (approx.)Elongation% , at 30°C 70 %( minimum)Coverage1.5-2kg/ sq. m of mixed material in 2coats depending on surface conditions.Mix Ratio by weight, Pack – A Pack – B2.5:1Shelf Life 1Year in original sealed condition

Product Details:

STARPROOF WF-MB-602 is cold applied liquid
waterproofing membrane, specially designed from a
blend of special resin and rubber, reinforced with
special water repelling fillers, minerals stabilizers and
gelling agent.
USES
Ideal waterproofing system for concrete roofs,
polyurethane foam slabs, polyester built up roofs,
maintenance of existing roofs, masonry and concrete
walls, bathrooms, basements, bridges, decks, metal
surfaces etc. Used as a sandwich membrane in new
construction and as surface treatment on existing slabs
OUTSTANDING FEATURES
 STARPROOF WF-MB-602 is a highly elastic
product, and cures to a rubber like membrane
capable of withstanding severe cases of expansion,
contraction and deck movements.
 Highly resistant to oxidation, UV light and ozone
because of unique additives used in compounding
it. It does not crack.
 More durable than normal asphalt coating and lasts
longer than most other coatings.
 Superior wetting and adhesion properties ensure
durable bond and resistance to peeling, chipping,
and/or separation and a longer life.
 Has the unique property of adapting itself over the
irregular contours of the deck and forming a
waterproof and impervious blanket.
 Single component, cold applied requiring no
mixing or heating; saves labor costs.
PACKING

 STARPROOF WF-MB-602 is available in 20 kg
Pail
Other Details:
Rubberized Elastomeric Waterproof Coating
A quality product of SSPL

Product Details:

DR. FIXIT Bitufix is an easy-to-apply cold applied Bitumen emulsion that can be used for damp proofing course of below ground structures It is an emulsified thixotropic bitumen protective coating. The coating dries to form a black flexible protective film. The finished film forms a tough barrier to vapor transmission.

Product Details:

The Waterproofing Sealing Tape Butyl Tape Expansion Joint Tape, measuring 10 meters in length, is a specialized tape designed for sealing and waterproofing applications in construction and building maintenance. Here's an overview of its features and uses:

1. Butyl Rubber Composition: The tape is primarily composed of butyl rubber, a synthetic rubber known for its excellent waterproofing properties and adhesion to various surfaces. Butyl rubber offers high elasticity, durability, and resistance to weathering, making it ideal for outdoor applications.

2. Sealing and Waterproofing: The butyl tape is specifically formulated to provide a reliable seal against water, moisture, air, and dust ingress. It creates a watertight barrier when applied to joints, seams, and gaps in building materials such as concrete, metal, wood, and plastic.

3. Expansion Joint Tape: The tape is suitable for use as an expansion joint filler in concrete structures. It accommodates the movement of building materials caused by thermal expansion, contraction, and structural settlement, preventing cracks and water infiltration in expansion joints.

4. Flexible and Conformable: The butyl tape exhibits excellent flexibility and conformability, allowing it to adhere tightly to irregular surfaces and contours. It can be easily molded and shaped to fit around pipes, corners, and protrusions, ensuring complete coverage and sealing effectiveness.

5. Easy Application: The tape features a self-adhesive backing that enables quick and easy application without the need for additional adhesives or tools. Simply peel off the protective backing and apply the tape directly to the desired surface, pressing firmly to ensure proper adhesion.

6. Versatile Use: The butyl tape is suitable for a wide range of applications in construction, including:

   • Roofing and flashing repairs
   • Window and door sealing
   • HVAC ductwork sealing
   • Pipe and conduit sealing
   • Waterproofing of expansion joints, concrete joints, and cracks
   • Automotive and RV repairs

7. Weather Resistance: The tape is designed to withstand harsh environmental conditions, including exposure to UV radiation, extreme temperatures, rain, and humidity. Its durable construction ensures long-term performance and reliability in outdoor and indoor environments.

8. Length: The tape comes in a convenient 10-meter roll, providing ample coverage for multiple sealing and waterproofing projects. The generous length minimizes waste and ensures cost-effectiveness for various applications.

Product Details:

CICO TAPECRETE P-151
A Surface Treatment System for Protecting Concrete & Masonry
CICO TAPECRETE P-151, popularly known as
TAPECRETE is an acrylic based Polymer
Modified Cementitious Flexible Composite
coating system. CICO TAPECRETE P-151 in
conjunction with cement provides properties
to combat the shortcomings of plain cement,
particularly its poor adhesion properties, low
impact strength, low flexural strength and thin
section fragility. CICO TAPECRETE P-151
polymer adds to the potential use as well as
enhances the properties of cement slurry/
mortar/concrete making them excellent
choice for use in new as well as renovation
work.
USES
CICO TAPECRETE P-151 is used for surface
treatment, protecting, waterproofing and
repairing concrete and masonry.
Waterproofing of basements, toilets, terraces,
roofs, swimming pools, water towers etc.
General concrete repairs. Protection of
concrete against corrosion, salt attack etc.
FEATURES
 Combines a tough, flexible, hard-wearing
surface with waterproofing.
 Allows trapped vapour to escape thus
preventing peeling and blistering.
 Can be applied in uniform thickness to
horizontal and vertical surfaces.
 Develops excellent bond to most building
materials.
 Reduces or prevents salt penetration into
concrete.
 Is not affected by ultraviolet light or by
chemicals ranging from mild acids to
strong alkalies.
 Is highly durable in continuous wet
condition.
 Is non-flammable and does not give off
toxic gases, when exposed to fire.
 Will not rot or corrode.
 Most properties improve with age.
 Is not harmful to the health of workman.
METHOD OF USE
Surface Preparation
Prior to application of CICO TAPECRETE P-151,
surface must be prepared as mentioned below
to avoid failure and to achieve maximum
beneficial properties.
 The surface shall be cleaned to remove all
dust, foreign matters, loose materials or
any deposits of contamination which
could affect the bond between the surface
and the CICO TAPECRETE P-151 coating.
This can be done by scarifying, grinding,
water blasting, sand blasting, and acid
washing or by any other approved
method.
 New flat surface like sub-base concrete
shall be made reasonably smooth so as
not to impede the application of CICO
TAPECRETE P-151 coating and to avoid
sharp projections.
 All concrete surfaces shall be thoroughly
pre-wetted prior to the application of
CICO TAPECRETE P-151 coating by pouring
water on flat surface or by spraying water
on vertical/inclined surfaces

Product Details:

The master builder's profession blends design and construction with wisdom and knowledge. Until the 18th century, this master builder was responsible for the design of a project and all phases of construction. The master builder had unquestioned authority over all aspects of the construction project

Product Details:

we “R.S. Enterprises” are a leading Wholesale Trader and Service Provider of a wide range of Waterproofing Chemical, Glass Railing, Fosroc Chemical, etc. 

Product Details:

Concrete, mortar, slurry should be prepared by using Sika® RainTite I enriched water and to be applied with in 20-30 minutes of preparation. In case of bond coat subsequent mortar or concrete to be applied when bond coat is fresh& tacky.

Product Details:

Asian Paints offers a diverse range of high-quality waterproofing chemicals designed to protect surfaces from water ingress and damage. Here's an overview of their waterproofing product line:

1. Asian Paints SmartCare Damp Proof: A specialized coating designed to prevent dampness and seepage on interior and exterior walls. It forms a waterproof barrier that repels water and prevents moisture from penetrating the substrate.

2. Asian Paints SmartCare Damp Proof Ultra: An advanced waterproofing solution formulated to provide long-lasting protection against dampness, seepage, and efflorescence. It offers superior adhesion, flexibility, and resistance to weathering.

3. Asian Paints SmartCare Crack Seal: A flexible sealant designed to fill cracks, gaps, and voids in concrete, masonry, and plaster surfaces. It forms a durable and waterproof seal, preventing water ingress and structural damage.

4. Asian Paints SmartCare Flexi Shield: A high-performance elastomeric waterproofing membrane that provides seamless protection against water penetration. It is flexible, UV resistant, and suitable for horizontal and vertical surfaces.

5. Asian Paints SmartCare Terrace Waterproofing System: A comprehensive waterproofing system that includes primers, coatings, membranes, and sealants designed specifically for terrace waterproofing. It offers complete protection against leaks and water damage.

6. Asian Paints SmartCare Aqua Seal: A versatile waterproofing solution suitable for a wide range of applications including roofs, basements, bathrooms, and water tanks. It provides excellent adhesion, flexibility, and durability.

7. Asian Paints SmartCare Tile Grout: A waterproof grout designed to fill gaps and joints between tiles in wet areas such as bathrooms and kitchens. It prevents water seepage and maintains the integrity of tiled surfaces.

8. Asian Paints SmartCare Instant Leak Stop: A quick-setting sealant that provides instant waterproofing for emergency repairs. It is ideal for sealing leaks in roofs, pipes, and concrete structures.

Polypropylene fiber, often abbreviated as PP fiber, is a synthetic fiber made from the polymer polypropylene. Here's an overview:

1. Composition: Polypropylene fiber is derived from polypropylene resin, a thermoplastic polymer. It is produced through a melt spinning process where the polymer is melted and extruded through fine nozzles to form fibers.

2. Properties: Polypropylene fibers possess several advantageous properties, including:

   • High tensile strength: Polypropylene fibers are strong and resistant to stretching.
   • Lightweight: Polypropylene fibers are lightweight, making them suitable for applications where weight is a concern.
   • Chemical resistance: Polypropylene fibers are resistant to most chemicals, acids, and alkalis.
   • Moisture resistance: Polypropylene fibers do not absorb moisture easily, making them suitable for outdoor and wet environments.
   • Low cost: Polypropylene fibers are relatively inexpensive compared to other synthetic fibers.
   • Abrasion resistance: Polypropylene fibers have good resistance to abrasion and wear.

3. Applications: Polypropylene fibers find a wide range of applications in various industries, including:

   • Concrete reinforcement: Polypropylene fibers are added to concrete mixes to improve crack resistance, impact resistance, and durability.
   • Nonwoven fabrics: Polypropylene fibers are used in the production of nonwoven fabrics for applications such as geotextiles, filtration, upholstery, and hygiene products.
   • Textiles: Polypropylene fibers are used in the production of textiles such as ropes, carpets, upholstery fabrics, and apparel.
   • Packaging: Polypropylene fibers are used in packaging materials such as bags, sacks, and packaging straps.
   • Automotive: Polypropylene fibers are used in automotive applications such as car interiors, seat covers, and carpets.

4. Types: Polypropylene fibers are available in various types, including monofilament fibers, multifilament fibers, staple fibers, and fibrillated fibers. Each type has specific properties and applications.

Foam backer rods, also known as caulking rods or expansion joint fillers, are cylindrical foam materials used in construction to control the depth and provide support for sealants in joints and gaps. Here's a comprehensive overview:

1. Material Composition: Foam backer rods are typically made from closed-cell polyethylene foam, although other materials such as open-cell foam or rubber may also be used. Closed-cell polyethylene foam is preferred for its compressibility, durability, and resistance to moisture absorption.

2. Sizes and Shapes: These backer rods come in various diameters and lengths to suit different joint sizes and applications. Common diameters range from 3mm to 50mm or more, while lengths typically vary from a few inches to several feet. Standard shapes include cylindrical and round profiles, although some specialized shapes may be available for specific applications.

3. Functionality: The primary function of foam backer rods is to act as a backing material for sealants applied to joints and gaps. By inserting the backer rod into the joint before sealing, it helps control the depth of the sealant and ensures proper adhesion to the joint surfaces. Additionally, the backer rod provides support to the sealant, reducing its consumption and preventing excessive sagging or waste.

4. Compression and Flexibility: Foam backer rods are designed to be compressible and flexible, allowing them to conform to irregular joint shapes and maintain contact with the joint surfaces. This compressibility also enables the backer rod to expand and contract with temperature changes and structural movements, preventing gaps and ensuring a tight seal over time.

5. Installation: Installing foam backer rods is a straightforward process. Simply press the backer rod into the joint or gap to the desired depth using a blunt tool or roller. The backer rod should fit snugly but not be stretched or deformed during installation. Once in place, the sealant can be applied over the backer rod according to the manufacturer's instructions.

6. Compatibility: Foam backer rods are compatible with a wide range of sealants, including silicone, polyurethane, latex, and acrylic-based sealants. They can be used in both vertical and horizontal joints in various construction materials such as concrete, masonry, metal, wood, and plastic.

7. Benefits: Using foam backer rods in conjunction with sealants offers several benefits, including improved joint performance, reduced sealant consumption, enhanced weatherproofing, and increased joint longevity. They also help prevent three-sided adhesion of the sealant, which can lead to premature failure and water infiltration.

8. Applications: Foam backer rods find applications in a wide range of construction projects, including sealing expansion joints, control joints, perimeter joints, window and door frames, roofing systems, and other building envelope elements. They are commonly used in residential, commercial, and industrial construction as part of waterproofing, weatherproofing, and air sealing systems.

A 10mm backer rod is a cylindrical foam material used primarily in construction joints and expansion joints to control the depth and provide a backing for sealants. Here's an overview:

1. Size: The "10mm" designation refers to the diameter of the backer rod. It's important to match the diameter of the backer rod to the width of the joint to ensure proper fit and performance.

2. Material: Backer rods are typically made of closed-cell polyethylene foam, although other materials such as open-cell foam or rubber may also be used. Closed-cell polyethylene foam is preferred for its compressibility, flexibility, and resistance to moisture absorption.

3. Function: The primary function of a backer rod is to act as a bond breaker and support for sealants applied to the joint. By inserting the backer rod into the joint before sealing, it helps control the depth of the sealant and ensures proper adhesion to the joint surfaces.

4. Compression: Backer rods are designed to be compressible, allowing them to conform to irregular joint shapes and maintain contact with the joint surfaces. The compressibility of the backer rod also helps create a proper seal and prevents sealant waste by reducing the amount needed.

5. Installation: To install a backer rod, simply press it into the joint to the desired depth using a blunt tool or roller. The backer rod should fit snugly but not be stretched or deformed during installation.

6. Compatibility: Backer rods are compatible with a wide range of sealants, including silicone, polyurethane, and latex-based sealants. They are suitable for use in both vertical and horizontal joints in various construction materials such as concrete, masonry, metal, and wood.

7. Benefits: Using a backer rod in conjunction with sealants provides several benefits, including improved joint performance, reduced sealant consumption, enhanced weatherproofing, and increased joint longevity.

8. Applications: Backer rods are commonly used in construction projects for sealing expansion joints, control joints, perimeter joints, and other types of movement joints in buildings, bridges, highways, and other structures.

Standard backer rods, also known as foam backer rods or caulking rods, are cylindrical foam materials used in construction joints, expansion joints, and other applications to control the depth and provide a backing for sealants. Here's an overview:

1. Material: Standard backer rods are typically made of closed-cell polyethylene foam, although other materials such as open-cell foam or rubber may also be used. Closed-cell polyethylene foam is preferred for its compressibility, flexibility, and resistance to moisture absorption.

2. Sizes: Standard backer rods are available in various diameters and lengths to accommodate different joint sizes and applications. Common diameters range from 3mm to 50mm or more, with standard sizes typically including 6mm, 10mm, 12mm, 15mm, and 20mm.

3. Function: The primary function of a standard backer rod is to act as a bond breaker and support for sealants applied to the joint. By inserting the backer rod into the joint before sealing, it helps control the depth of the sealant and ensures proper adhesion to the joint surfaces.

4. Compression: Standard backer rods are designed to be compressible, allowing them to conform to irregular joint shapes and maintain contact with the joint surfaces. The compressibility of the backer rod also helps create a proper seal and prevents sealant waste by reducing the amount needed.

5. Installation: To install a standard backer rod, simply press it into the joint to the desired depth using a blunt tool or roller. The backer rod should fit snugly but not be stretched or deformed during installation.

6. Compatibility: Standard backer rods are compatible with a wide range of sealants, including silicone, polyurethane, and latex-based sealants. They are suitable for use in both vertical and horizontal joints in various construction materials such as concrete, masonry, metal, and wood.

7. Benefits: Using a standard backer rod in conjunction with sealants provides several benefits, including improved joint performance, reduced sealant consumption, enhanced weatherproofing, and increased joint longevity.

8. Applications: Standard backer rods are commonly used in construction projects for sealing expansion joints, control joints, perimeter joints, and other types of movement joints in buildings, bridges, highways, and other structures.

Heat reflective paint, also known as cool roof paint or thermal insulation paint, is a specialized coating designed to reduce heat absorption and transfer on building surfaces, thereby lowering indoor temperatures and improving energy efficiency. Here's an overview of heat reflective paint:

1. Composition: Heat reflective paint is formulated with special pigments, additives, and binders that reflect sunlight and infrared radiation, rather than absorbing them like traditional paints. These reflective properties help to reduce surface temperatures and minimize heat transfer into the building.

2. Reflective Pigments: The key component of heat reflective paint is its reflective pigments, which are typically made from materials such as titanium dioxide or ceramic microspheres. These pigments have high solar reflectance (also known as albedo) and emissivity, enabling them to reflect a significant portion of the solar energy away from the painted surface.

3. Low Thermal Conductivity: Heat reflective paints often contain additives or fillers that reduce thermal conductivity, further minimizing heat transfer through the painted surface. This helps to keep the underlying building materials cooler and reduces the need for energy-intensive cooling systems.

4. Application Surfaces: Heat reflective paint can be applied to a variety of surfaces, including roofs, exterior walls, concrete decks, metal structures, and asphalt pavements. It is suitable for both horizontal and vertical surfaces and can be used on new constructions or applied as a retrofit coating to existing structures.

5. Benefits:

   • Energy Savings: By reducing heat absorption and lowering indoor temperatures, heat reflective paint can lead to significant energy savings by reducing the need for air conditioning and cooling systems.
   • Comfort: Heat reflective paint helps to create a more comfortable indoor environment by reducing heat buildup and minimizing temperature fluctuations.
   • Extended Roof Lifespan: By reducing thermal stress and UV exposure, heat reflective paint can extend the lifespan of roofing materials and reduce maintenance costs.
   • Environmental Impact: Heat reflective paint contributes to environmental sustainability by reducing energy consumption, lowering greenhouse gas emissions, and mitigating the urban heat island effect.
   • Regulatory Compliance: Many heat reflective paints meet or exceed energy efficiency standards and green building codes, making them eligible for incentives, rebates, and certifications.

6. Application Methods: Heat reflective paint can be applied using standard painting techniques such as brushing, rolling, or spraying. Multiple coats may be required to achieve the desired level of reflectivity and coverage.

7. Color Options: Heat reflective paint is available in a variety of colors and finishes to suit different aesthetic preferences and architectural styles. However, lighter colors typically offer higher solar reflectance and better heat reduction properties.

8. Durability and Maintenance: High-quality heat reflective paints are formulated to withstand harsh weather conditions, UV exposure, and environmental pollutants. Routine maintenance, such as cleaning and periodic recoating, can help maximize the longevity and performance of the painted surface.

Concrete waterproofing admixture is a specialized additive used in concrete mixtures to enhance the waterproofing properties of concrete structures. Here's an overview of concrete waterproofing admixture:

1. Composition: Concrete waterproofing admixtures are typically chemical formulations containing various water-repellent compounds, surface-active agents, and pore-blocking additives. These ingredients work together to reduce the permeability of concrete, making it more resistant to water penetration.

2. Water Repellency: The primary function of concrete waterproofing admixtures is to impart water-repellent properties to the concrete matrix. They reduce the surface tension of water and create a hydrophobic barrier within the concrete pores, preventing water molecules from penetrating the structure.

3. Types of Admixtures:

   • Hydrophobic Admixtures: These admixtures contain water-repellent compounds such as fatty acids, waxes, or silicone-based materials. They form a barrier on the surface of cement particles, reducing water absorption and improving the waterproofing performance of concrete.
   • Pore Blocking Admixtures: These admixtures consist of fine particles that fill the capillary pores and micro-cracks in the concrete, effectively blocking the passage of water. They improve the density and impermeability of the concrete matrix, reducing water ingress and moisture-related damage.
   • Crystalline Admixtures: Crystalline waterproofing admixtures contain reactive chemicals that react with moisture and free lime in the concrete to form insoluble crystals. These crystals grow within the concrete pores, effectively sealing them and enhancing the waterproofing performance of the concrete.
   • Integral Waterproofing Admixtures: Integral waterproofing admixtures are added directly to the concrete mix during batching, providing uniform waterproofing protection throughout the entire structure. They are suitable for a wide range of concrete applications, including foundations, basements, tunnels, and swimming pools.

4. Benefits:

   • Improved Durability: Concrete waterproofing admixtures enhance the durability and longevity of concrete structures by reducing water penetration, freeze-thaw damage, and chemical ingress.
   • Reduced Maintenance: Waterproofed concrete structures require less maintenance and repair over their service life, resulting in cost savings and extended maintenance intervals.
   • Enhanced Structural Integrity: By minimizing water ingress and moisture-related deterioration, waterproofing admixtures help preserve the structural integrity and load-bearing capacity of concrete elements.
   • Increased Sustainability: Waterproofed concrete structures have reduced environmental impact due to lower water consumption, energy usage, and material wastage associated with maintenance and repair activities.
   • Improved Indoor Air Quality: Waterproofing admixtures help prevent moisture buildup and mold growth within enclosed spaces, contributing to healthier indoor air quality and occupant comfort.

5.  

Tapecrete is a specialized waterproof coating chemical manufactured by Pidilite Industries Limited, designed to provide effective waterproofing and protection for concrete and masonry surfaces. Here's an overview of Tapecrete waterproof coating:

1. Composition: Tapecrete is a cementitious waterproofing compound that consists of a blend of Portland cement, graded aggregates, polymers, and proprietary additives. This unique formulation creates a durable and flexible coating that effectively seals and protects concrete and masonry substrates from water ingress.

2. Waterproofing Properties: Tapecrete forms a seamless and waterproof membrane when applied to the surface, preventing water penetration and moisture migration. It effectively seals cracks, voids, and capillary channels in the substrate, providing long-lasting protection against water leakage, dampness, and efflorescence.

3. Adhesion and Bonding: Tapecrete exhibits excellent adhesion to various substrates, including concrete, masonry, brickwork, and plaster. It forms a strong bond with the substrate, ensuring reliable performance even in demanding conditions. Proper surface preparation is essential to maximize adhesion and bonding strength.

4. Flexibility and Crack Bridging: One of the key features of Tapecrete is its flexibility, allowing it to accommodate substrate movement, thermal expansion and contraction, and minor structural cracking. The flexible nature of the membrane enables it to bridge hairline cracks and withstand dynamic stresses without compromising waterproofing integrity.

5. Breathability: Despite its waterproofing properties, Tapecrete maintains the breathability of the substrate, allowing trapped moisture to escape and preventing the buildup of hydrostatic pressure. This breathability helps preserve the structural integrity of the substrate and minimizes the risk of deterioration due to moisture-related issues.

6. Application: Tapecrete is typically applied as a brush-applied slurry or spray-applied coating onto the prepared substrate surface. Multiple coats may be required to achieve the desired thickness and waterproofing performance. The coating cures to form a tough, resilient membrane within a specified time, depending on ambient conditions.

7. Versatility: Tapecrete is suitable for a wide range of applications, including:

   • Waterproofing of basements, foundations, retaining walls, and podium decks
   • Protection of water tanks, reservoirs, swimming pools, and water features
   • Sealing of roofs, terraces, balconies, and wet areas in bathrooms and kitchens
   • Rehabilitation and repair of existing concrete structures to prevent water ingress and deterioration

8. Quality Assurance: Tapecrete undergoes rigorous quality control testing to ensure compliance with industry standards and specifications. The product is manufactured in state-of-the-art facilities using advanced technology and quality management systems, providing assurance of consistent quality and performance.